View previous topic :: View next topic |
Author |
Message |
crakemarsh
Joined: 18 Apr 2008 Posts: 5 Location: Uttoxeter, Staffs
|
Posted: Sat Apr 19, 2008 3:30 pm Post subject: starting problems |
|
|
Just collected Gts from dealer on its service. Bike has Pm pipe and electronic gizmo. Now having problems starting tho never did before the dealer got mits on it. It needs the starter holding on for a while then a fistful of accelerator and even then I need to rev it for a minute or two before it will tick over correctly or it will just cut out.
Dealer says they didnt get involved in the tuning parts at all and just ignored any diagnostic readouts that would have thrown up because of the pipe etc.
Also turned the key this morning and no power showing in the clocks,lights but then repeated it and everything ok again!
Wots goin on???? |
|
Back to top |
|
|
Castle-Barber Inspector
Joined: 27 Feb 2008 Posts: 449 Location: Chesterfield
|
Posted: Sat Apr 19, 2008 3:58 pm Post subject: |
|
|
Is it the PM Tuning Fuel Injection Module kit that plugs into the scooter EFI......Or the one of Motorsport.....
The dealer needs set this up if you have asked him or else the pulse widths / Main jet / fuel enrichment Will be all tits up.......
And it will run like a bag of spanners....
I sounds like this has happend if you need to push fuel though to help it start.....
Regards Mark....
Last edited by Castle-Barber on Sat Apr 19, 2008 6:30 pm; edited 1 time in total |
|
Back to top |
|
|
Maver Site Admin
Joined: 14 May 2007 Posts: 2193 Location: naaaaaarfolk we drive tractors and talk loike PIRATES
|
Posted: Sat Apr 19, 2008 4:20 pm Post subject: |
|
|
sounds like the dealer serviced it and set it up "according to the book" and as castlebarber says the module needs different settings. _________________
|
|
Back to top |
|
|
smudger Guvernor
Joined: 07 Oct 2007 Posts: 1066 Location: The Wirral; the bit of land between the Mersey and the Dee
|
Posted: Sat Apr 19, 2008 4:27 pm Post subject: |
|
|
So is the best advice here to disconect the EFI module thingy before letting the dealer get his mits on it?
Only asking as I have one on it's way from Motorsports.com _________________
|
|
Back to top |
|
|
crakemarsh
Joined: 18 Apr 2008 Posts: 5 Location: Uttoxeter, Staffs
|
Posted: Sat Apr 19, 2008 5:38 pm Post subject: |
|
|
Yes just to confirm that its the PM fuel module. it was already set up for the pipe etc so just plug & go. As i said it has all worked fine before this supposedly standard service and they say they have just left it alone but something has changed. |
|
Back to top |
|
|
Castle-Barber Inspector
Joined: 27 Feb 2008 Posts: 449 Location: Chesterfield
|
Posted: Sat Apr 19, 2008 6:38 pm Post subject: |
|
|
crakemarsh wrote: | Yes just to confirm that its the PM fuel module. it was already set up for the pipe etc so just plug & go. As i said it has all worked fine before this supposedly standard service and they say they have just left it alone but something has changed. |
yeh it sounds likes to me they have mest about with the settings.....
But will deny doing so I bet
I have the PM One on my Scoot with a PM68 Pipe all i do is take it off before service then pop it back on after...... |
|
Back to top |
|
|
Castle-Barber Inspector
Joined: 27 Feb 2008 Posts: 449 Location: Chesterfield
|
Posted: Sat Apr 19, 2008 6:41 pm Post subject: |
|
|
smudger wrote: | So is the best advice here to disconect the EFI module thingy before letting the dealer get his mits on it?
Only asking as I have one on it's way from Motorsports.com |
Yes do not let them touch it ......... Take it off then put it back on after the service.....
Do you have a standard pipe on the the scoot for the motorsport one.... |
|
Back to top |
|
|
CheekyThomas Guvernor
Joined: 18 May 2007 Posts: 1374
|
Posted: Sat Apr 19, 2008 9:48 pm Post subject: |
|
|
Theres not much the dealer can have done to alter the PM box... Did they update the bikes ECU with the new software from Piaggio... if so ignore the dodgy running for the 1st 30miles as they do run like a dog until the ECU has relearnt whats going on... |
|
Back to top |
|
|
crakemarsh
Joined: 18 Apr 2008 Posts: 5 Location: Uttoxeter, Staffs
|
Posted: Sat Apr 19, 2008 10:00 pm Post subject: |
|
|
sounds like that will be it, I know its not been updated upto now so I'll have to check with them. Hopefully then by tomorrow problem may be sorted (over 30miles).
Thanks |
|
Back to top |
|
|
|